Copyright © Kingseal Co. Ltd. Thailand 2010. All Rights Reserved.
 
Piston Seals
 
Rod Seals
 
Oil Seals
 
 
O-Rings And Static Seals
U-Seal Piston And Rod
 
Piston Seals (P)
Made To Order Machined Seals
Rod Seals (R)
Back-Up Rings (B)
Lip Seals (LS)
Wipers (W)
 
Rod Wipers
 
Wear Rings
 
Quantum   124

    * Viscosity 20cP
    * Low Viscosity
    * Quick Cure

Difficult Rubber Offers aggressive bonding on tough to bond rubber compounds. Excellent O-ring bonder.
EF® Primer 50
(Green Liquid)

Hernon® EF® Primer 50 is designed to increase the cure speed of Hernon®  anaerobic adhesives and sealants including Nuts N’ Bolts®, Dripstop® and Cylinlock®. Long-term pretreatment is available with an on-part life of up to 30 days. EF® Primer 50 is especially recommended for large gap bonds and inert metals.
Gasket Replacer® 910
(Purple Gel)

    * Multi-Purpose
    * Stays Flexible

Gasket Replacer 910 is a general purpose product. It is a smooth gel that is easily applied and cures after confinement into a thin, tough, flexible, resilient and reliable seal. It flexes with flanges during pressure and/or thermal cycling, and withstands vibration effects. Fills gaps to .010" unprimed, .050" primed. Excellent supplement to dress hard or soft precut gaskets. Assures adequate gasket performance on less than optimum flange faces. Suitable for application by tracing, screen-printing, and roll coating. Use to replace all gaskets up to .030" thick.

Applications:

    * Gearbox covers
    * Vacuum pump flanges
    * Fuel and water pumps
    * Automotive and truck axle covers
    * Pump couplings
    * Fuel tanks on chain saws
    * Power-take-off covers
Hernon Nuts N’ Bolts®   427 is a single component anaerobic thread locking material, which develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. Sold as a pack (10/pk).
Instantbond® 113

Viscosity 40cP
Low Viscosity
General Purpose

This thin liquid is suitable for close tolerance bonding of a wide variety of materials.
 
Fusionbond 37784
Fusionbond 370
Fusionbond 371
Dissipator 746
Dissipator 745
ReAct 730
ReAct 727
ReAct 761
Fusionbond 375
Tuffbond 313

Tuffbond 309

Tuffbond 305
Polycure 744
HASA 720
HASA 716
HASA 718
Instabond 110
Instabond 123
Instabond 127
Quantum 108
Ultrabond 740
Ultrabond 748
Ultrabond 758
Hernon Products
Click on the images to enlarge...
Unique Liquid Engineered Sail and Track Lubrication
Smooth®™ Fuse SF10 500mL
Smooth® Fuse
Uses

Smooth® Fuse SF10 is primarily formulated to clean and lubricate PTFE and metal surfaces of flat bed and conveyor fusing presses utilised in the garment manufacturing industry for the application of fusible interlinings onto garment sections. Polyester, Polyamide and other adhesives used in fusible interlinings become molten when heat is applied during the fusing process.  For a variety of reasons some of the molten adhesive commonly becomes misplaced and adheres to conveyor belt or platen surfaces, to scraper blades, wiper/cleaning devices and to other sections of the presses.


Smooth® Fuse is designed to clean surfaces contaminated with adhesive and residue, to act as a preventative agent by lubricating surfaces likely to become contaminated and to loosen hard compacted residue on PTFE coated conveyor belts and platen covers.  When used in accordance with the manufacturer’s instructions Smooth® Fuse will:

• Reduce maintenance and down time associated with heavy adhesive contamination of fusing surfaces.
• Reduce material sticking problems caused by sticky fusing surfaces.
• Reduce wastage caused by fabric contamination from dirty fusing surfaces. 
• Extend PTFE surface belt and cover life.

One of the unique features of Smooth® Fuse is that as a preventative solution it can be used continuously while the fusing operations are taking place.

How to use Smooth Fuse


Section 1.  As a preventative barrier lubricant for clean fusing surfaces

One of the most effective and unique cleaning/lubricating properties of Smooth® Fuse is the barrier it creates between potential adhesive contamination and the PTFE coated surfaces of fusing press conveyor belts and platen covers. This barrier prevents adhesive from sticking to the belts/platens and from forming a hard residue when the belts/platens cool down.  The Smooth™ Fuse barrier also prevents adhesive contamination building up on scrapers and other sections of the fusing press. This preventative barrier will work most effectively if belts and platen surfaces are kept free from contamination by ensuring that, using the machine’s wiper systems or by hand, the residue is cleaned from belts/platens as the adhesive is released. It is important therefore that the cleaning systems and surfaces are regularly inspected and for example, new cleaning cloth on wiper systems is regularly exposed.

Action:

• In the case of a conveyor fusing press ensure that the cleaning/wiper system has new wiper materials fitted for both upper and lower PTFE belts

• Heat up the fusing press to normal fusing temperature (about 150°C) and apply a coating of Smooth® Fuse over the full area of the belts/platen.

• In the case of conveyor machines the wiper materials should become saturated with Smooth® Fuse. The wipers will then continue to apply a light coating of   Smooth® Fuse onto the belts to provide a barrier to the adhesive while the fusing operations are taking place.  In the case of platen machines or ineffective/non existent wiper systems, Smooth® Fuse can be regularly sprayed directly on to the PTFE surfaces.

• Where relevant replace wiper materials and clean scraper blades regularly.

• Apply Smooth® Fuse regularly (normally at least hourly) subject to the amount of adhesive contamination being experienced.


Section 2 As a cleaning agent for contaminated conveyor belts and cleaning systems

Action:

• In the case of a conveyor fusing press ensure that the cleaning/wiper system of the fusing press has new wiper materials fitted for both upper and lower PTFE belts.
• Heat up the fusing press to normal fusing temperature (about 150°C) and apply a coating of Smooth® Fuse over the full area of the belts. (see safety below)

• Allow the machine to run for a few minutes applying more Smooth® Fuse as necessary.
• If the belts are heavily contaminated the wipers may become saturated with adhesive residue quite quickly as Smooth® Fuse releases the contamination. Either a new surface of the wiper materials needs to be exposed, or new wiper materials need to be fitted. This will need to be repeated until the belts are clean. The cleaning process for PTFE coated belts/platens can be carried out by hand using a rough cloth and insulated gloves.  This is often done while the machine is cooling down but the adhesive contamination is still molten or at the end of a production cycle.


• Clean scrapers if the machine is fitted with these.

• When belts are clean replace the wiper materials for upper and lower belts.

• While the machine is still hot and running, apply another coating of Smooth® Fuse. In the case of conveyor machines the wiper materials should become saturated with Smooth® Fuse. The wipers will then continue to apply a light coating of Smooth® Fuse onto the belts to provide a barrier to the adhesive while the fusing operations are taking place.  In the case of platen machines Smooth® Fuse can be regularly sprayed directly onto the PTFE surfaces.

• Where relevant replace wiper materials and clean scraper blades regularly.

• Apply Smooth® Fuse regularly (normally at least hourly) subject to the amount of adhesive contamination being experienced.
Availability Formats

500 ml trigger spray bottles
5 litre containers - with or without heavy duty spray applicator


Important

Safety

1. We recommend avoiding eye and repeated skin contact. Do not allow skin to come in contact with hot fusing press surfaces.  Use insulated gloves.  Always follow the fusing press manufacturers maintenance and machine operating instructions when carrying out any of the operations above.


Using Smooth® Fuse

2.  Removing the adhesive residue once loosened by Smooth® Fuse is normally achieved by ensuring that the machine's 'wiper' system is working effectively. Once Smooth® Fuse is applied, the residue on the belts can also be cleaned by hand using a rough cloth and insulated gloves.  This can be more effectively carried out when the machine is cooling down or at the end of a production cycle
 
 
Kingseal supplies superior and innovative range of rod boots/bellows or expandable covers for the construction, mining, oil and gas, agriculture, steel mills and many other types of industrial applications.
•  Furnace Covers
•  Screw jack covers
•  Linear screw covers
•  Dust seals for Shaker Sizing Screen
•  Protective sleeves
Way Covers
NEONY - resistant to moderate chemicals, acids, oils, grease, ozone and many types of solvents.
Material
ALUMINIZED KEVLAR - an aramid blend fabric that is heat resistant, extra tough and extra flexible.
Benefits of Protective Coverings

Resistant to puncture, abrasions, flame, sparks, acids and chemicals
Reduce costly down time
Retaining grease
Extends machine life
Protect against dirt, dust and rocks
Eliminates pitting and scoring to cylinder shaft
Protection from abrasive particles and chips
Easy to install
 
Available Products
•  Expandable cylinder rod boots
•  Expandable gasket covers
•  Split rod covers
•  Expansion joints
•  Expandable discharge chutes
Bellows
Protective Bellows
 
Parker Brass Gland Kit
Heavy Equipment Seal Kits 2011
 
Kingseal Kits
Generic Seal Kits Catalog
Please contact Kingseal  for the new pricing of our Generic Seal Kits. This list price is out of date.